Knifemaking

This is a Loveless inspired knife blade blank made by Tak Fukuta in Seki, Japan for Explorer circa 1990s. It measures 8.25" long overall and the partially serrated blade measures 3.75" long and is made of polished AUS-8 just over 1/8" thick. Comes with...

This is beautiful bowie knife blade blank made by Tak Fukuta in Seki, Japan for Explorer circa 1990s. It measures 15" long overall and the blade measures 10" long and is made of mirror polished 3/16" thick AUS8 Stainless Steel. Blade only, guard not...

This is a knife blade blank made by Tak Fukuta in Seki, Japan circa 1990s. This blank measures 8.625" long overall and the blade measures 4.5" long and is made of mirror polished AUS-8A. Measures just over 1/8" thick. Tak Fukuta was the first Japanese...

This is a knife blade blank made by Tak Fukuta in Seki, Japan circa 1980s for Boker Magnum. The 440 Stainless blade is a hefty 5/32" thick and is mirror polished and measures 8.8" long overall and the blade measures 3.5" long. Tak Fukuta was the first...

This is a knife blade blank made by Tak Fukuta in Seki, Japan circa 1980s. The 440 Stainless blade is a hefty 5/32" thick and is mirror polished and measures 8.8" long overall and the blade measures 3.5" long. Tak Fukuta was the first Japanese member of...

This is a knife blank from the original run of 1226 and made in Seki, Japan circa 1980 by Tak Fukuta for Ka-Bar. It has the original Olean, NY tang stamp with stainless steel blade and comes with the guard and pommel and about half the handle with...

This is a knife blank from the original run of 1226 and made in Seki, Japan circa 1980 by Tak Fukuta for Ka-Bar. It has the original Olean, NY tang stamp with stainless steel blade and comes with the guard and pommel. Tak Fukuta was the first Japanese...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Junglee circa 2000. It measures 9.25" long overall (with handle) and the blade measures 5.2" long and is made of polished 5/32" thick ATS-34 and etched with JUnglee Tak Fukuta and 2000 in...

This is a Case XX 1990 LT216-5 knife unfinished blade blank. The blade measures 5.25" long and overall measures 9.25" and is just under 1/8" thick. It is satin finished stainless steel and is unsharpened with 1990 tang stamp...

This is a set of four standoffs and eight screws for the Buck 889 Strider. These are parts made for a custom Buck 889 Strider project from several years ago. An example of these on a customized 889 is shown in picture (not included). They are made of...

This is the original Spyderco pocket clip marked with logo from circa 1990s. Measures 2-5/8" long overall. The distance between 2 outer holes (on center) is 11/32". Specs Brand/Model: Spyderco Pocket Clip Made...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Explorer circa 1990s. It measures 6" long overall and the blade measures 4.625" long and is made of polished 5/32" thick AUS-8A. Comes with Stainless steel guard, needs filing to final fit...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Browning circa 1990s. It measures 9" long overall and the blade measures 4.125" long and is made of polished 3/16" thick AUS-8A. Comes with Stainless steel guard, needs filing to final fit...

This is a knife blade blank made by Tak Fukuta in Seki, Japan circa 1990s. This blank measures 10.625" long overall and the blade measures 5.625" long and is made of mirror polished AUS-8A. Measures just over 1/8" thick. Tak Fukuta was the first Japanese...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Browning circa 1990s. It measures 8.625" long overall and the blade measures 4.625" long and is made of AUS-8A. Tak Fukuta was the first Japanese member of the American Knife Maker's...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Browning circa 1990s. It measures 9.5" long overall and the blade measures 5" long and is made of polished AUS-8A. Tak Fukuta was the first Japanese member of the American Knife Maker's...

These are Ka-Bar Thorn knife blades made in Seki, Japan. They are sharpened with thumb stud with handling wear and may have light staining mainly on sharpened area. Blade edge is unused. Measures 3-3/4" long overall and 0.118" thick...

This is a lockback blade from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is polished and has been heat treated/hardened, it is unsharpened and the edges have not been finished. It is made of ATS-34 and measures 3-3/4" long overall...

These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is rough ground and has been heat treated/hardened. It is made of ATS-34 and measures 3-7/16" long overall and measures 0.98" thick. This is...

These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is rough ground and has been heat treated/hardened. It is made of ATS-34 and measures 3-3/4" long overal land measures 0.99" thick. This is...

These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is rough ground and has not been heat treated/hardened. It is made of ATS-34 and comes with backspring and spacer. These need finished,...

These are unfinished folding knife parts by Seizo Imai in Seki, Japan circa 1990s. The blade is rough ground and has not been heat treated/hardened. It is made of 0.119" thick VG-10 core damascus and comes with the handle and pivot. Needs finished and...

These nickel silver handle spacers are precision water jet cut. This simplifies a knife project because cutting by hand can bend the material it easily. Designed to be installed as decorative spacers on each side of flat scale knife handles, these may be...

These are knifemaking Copper handle spacers. They are new water jet cut and just need a fitting and buffing. Made in Spokane WA, USA. Overall exterior size: 0.040" thick x 15/16" wide x 1 5/8" tall. Approximate cutout in center: 0.25" X 0.75". Made to...