Knife Making

If you are searching for an excellent quality hunter knifemaking project look no further. This fixed knife was made in Seki, Japan by Nakamura circa 1980s for BST. It comes with aging tarnish on blade, but can wipe off nearly completely by hand (this...

This is a well designed knife blade blank made by Tak Fukuta in Seki, Japan for Explorer circa 1980s. It measures 8.4" long overall and the blade measures 4.25" long and is made of polished AUS-8 at 0.140" thick and has a hidden tang. Blade only, no...

This is a well designed knife blade blank made by Tak Fukuta in Seki, Japan for Explorer circa 1980s. It measures 8.6" long overall and the blade measures 4.2" long and is made of polished AUS-8 just over 1/8" thick and has a tapered tang. Blade only, no...

This is a set of four standoffs and eight screws for the Buck 889 Strider. These are parts made for a custom Buck 889 Strider project from several years ago. An example of these on a customized 889 is shown in picture (not included). They are made of...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Mac circa 1990s. This blank measures 10.25" long overall and the blade measures 5" long and is made of AUS-8A. Measures just under 1/8" thick. Comes with wood scales, designed to have...

This is a Browning knife blade blank made in Seki, Japan circa 1990s. It measures 8.625" long overall and the blade measures 4.625" long and is made of AUS-8A. Specs Brand/Model: Browning Wasatch Guthook Skinner Made...

This is a Browning knife blade blank made in Seki, Japan circa 1990s. It measures 9.5" long overall and the blade measures 5" long and is made of polished 3/16" thick AUS-8A. Specs Brand/Model: Browning Wasatch Guthook...

This is the Jess Horn folder pattern. Perfect for the knifemaker! These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan, made circa 1990s. The blade is rough ground and has been heat treated/hardened. Formed of ATS-34 steel,...

These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is rough ground and has been heat treated/hardened. It is made of ATS-34 and measures 3-3/4" long overal land measures 0.99" thick. This is...

These are unfinished folding knife parts from the Seizo Imai factory in Seki, Japan made circa 1990s. The blade is rough ground and has not been heat treated/hardened. It is made of ATS-34 and comes with the rocker (spring not included). These need...

These are unfinished folding knife parts by Seizo Imai in Seki, Japan circa 1990s. The blade is rough ground and has not been heat treated/hardened. It is made of 0.119" thick VG-10 core damascus and comes with the handle and pivot. Needs finished and...

These nickel silver handle spacers are precision water jet cut. This simplifies a knife project because cutting by hand can bend the material it easily. Designed to be installed as decorative spacers on each side of flat scale knife handles, these may be...

These are knifemaking Copper handle spacers. They are new water jet cut and just need a fitting and buffing. Made in Spokane WA, USA. Overall exterior size: 0.040" thick x 15/16" wide x 1 5/8" tall. Approximate cutout in center: 0.25" X 0.75". Made to...

This is an excellent quality USA made Titanium pocket clip by USAKnifeMaker.com. One of our customers found that the screw placement matches the Benchmade standard clip footprint perfectly. We purchased for a project a few years ago but never used...

This is a knife blade blank made by Tak Fukuta in Seki, Japan for Rigid circa 1980s. It measures 5/32" thick and is 13.5" long overall and the blade measures 9.125" long. Comes with original brass guard (will require filing to fit). Tak Fukuta was the...

This is a Case XX 1990 Rio Grand bowie knife unfinished blade blank. The blade measures 10.125" long and overall measures 15" and is just under 1/4" thick. It is satin finished stainless steel and is unsharpened with 1990 tang stamp and has a tapered...

Vintage "NOS" Valor butterfly knife kit! This is a very rare opportunity to own an original vintage Valor 566 Seki, Japan handle in new old stock condition with black Korea blade. Acquired directly from Valor years ago, this is an unassembled kit,...

This is a very rare opportunity to own an original vintage AUS6 blade, made in Seki, Japan in unused condition with shop/storage wear (blade edge may be imperfect). Blade stamped "Seki  Japan." Great fit for Valor and similar Parkers also from the...

This is a very rare opportunity to own an original vintage Valor AUS6 blade that is made to fit the Valor 566, made in Korea in new old stock condition (blade edge may be imperfect). This Valor Korean blade, marked "Stainless Steel Korea" is for the...

These are knifemaking Brass handle spacers. They are new water jet cut and just need a fitting and buffing. Made in Spokane WA, USA. Overall exterior size: 0.040" thick x 15/16" wide x 1 5/8" tall. Approximate cutout in center: 0.25" X 0.75". Made to fit...

These copper handle spacers are precision water jet cut. This is nice because copper is so soft that cutting it in this thickness by hand can bend it easily. Designed to be installed as decorative spacers on each side of flat scale knife handles, these...

These are nice Nickel Silver knife handle spacers. They are new water jet cut and just need a fitting and buffing. Made in Spokane WA, USA. Overall exterior size: 0.040" thick x 15/16" wide x 1 5/8" tall. Approximate cutout in center: 0.25" X 0.75". Made...

These are great Micarta handle spacers. Cut down on your production time with these pre-cut coffin-style spacers! They will work great for any blade design they fit. The Longer version works for a 1/4" thick blade and was designed for the Marbles...